@article { author = {Safi, M. and Shushtari, A.M. and Hemmati Nejad, N.}, title = {Effect of Enzymatic Hydrolysis on Physical Properties of Wool Fabric}, journal = {Journal of Textile Science and Technology}, volume = {2}, number = {1}, pages = {3-8}, year = {2012}, publisher = {Today Textile Institute}, issn = {2151-7162}, eissn = {2322-2417}, doi = {}, abstract = {In the present work, the effect of treatment time and enzyme concentration in protease hydrolysis on the physical properties of wool fabric is studied. The hydrolysis effects on the treated samples are evaluated by measuring weight loss, tensile strength (along the warp), area shrinkage, thickness and bending length as well as scanning electronic microscope (SEM) images. The results showed that despite the specific reduction in weight and tensile strength, the control of enzyme concentration at 3 % and treatment duration at 60 min as the optimum condition of enzyme application gives the desirable quality of thickness, shrinkage and bending length of the used fabric. In addition, the thickness of hydrolyzed fabric was decreased due to the removal of fuzz from the surface. The obtained results for the bending length illustrated that a soft handle is achieved on samples. Besides, the percentage of shrinkage was decreased by the removal of some parts of wool scales. However, at higher enzyme concentrations (above 3 %) the changes were leveled off.}, keywords = {Enzymatic hydrolysis,Protease,wool,time,Enzyme Concentration,physical properties}, title_fa = {تاثیر عملیات هیدرولیز آنزیمی بر خواص فیزیکی پارچه پشمی}, abstract_fa = {در تحقیق حاضر، تاثیر زمان عملیات و غلظت آنزیم در هیدرولیز با آنزیم پروتئاز بر خواص فیزیکی پارچه پشمی بررسی شده است. اثرات هیدرولیز بر نمونه های عمل شده با اندازه گیری کاهش وزن، استحکام (در جهت تار)، جمع شدگی (سطحی)، ضخامت و طول خمشی به همراه تصاویر میکروسکوپ الکترونی پو یشی ارزیابی گردید. نتایج نشان داد علی رغم کاهش معینی در وزن و استحکام، کنترل غلظت آنزیم در مقدار %3 و زمان عملیات 60 دقیقه به عنوان شرایط بهینه منجر به بهبود جمع شدگی، ضخامت و طول خمشی پارچه پشمی مورد استفاده می شود. به علاوه ضخامت پارچه به دلیل کنده شدن پرزهای سطحی در حین عملیات هیدرولیز آنزیمی، کاهش یافت. مقادیر به دست آمده برای طول خمشی، نشان دهنده زیر دست لطیف نمونه ها است. همچنین حذف فلس های موجود در سطح الیاف پشم منجر به کاهش درصد جمع شدگی منسوج گردید. اگرچه در غلظت های بالاتر آنزیم (بالای 3 درصد) شدت و میزان این تغییرات کاهش یافت.}, keywords_fa = {هیدرولیز آنزیمی,پروتئاز,پشم,زمان,غلظت آنزیم,خصوصیات فیزیکی}, url = {https://www.jtst.ir/article_483.html}, eprint = {https://www.jtst.ir/article_483_9e5c5d20d5321835506b52905a201a68.pdf} } @article { author = {Namiranian, B. and Modarresi, V.}, title = {Evaluation of Fabric Mechanical Properties on Worsted Fabric Moulding}, journal = {Journal of Textile Science and Technology}, volume = {2}, number = {1}, pages = {9-14}, year = {2012}, publisher = {Today Textile Institute}, issn = {2151-7162}, eissn = {2322-2417}, doi = {}, abstract = {Molding is one of the most important properties of textile fabrics. The ability of a fabric to be molded into 3D shapes is actually an important technical application in this study, worsted fabric with different structural parameters are provided and their moldability are assessed with a shear modulus, bending modulus and stretch modulus, and the results of shearing are obtained with analysis of image processing .a moldability tester is also developed in this research with the ability to measure the fabric moldability.}, keywords = {Molding,Sheer modules,Bending modules,Tensile modules}, title_fa = {بررسی تاثیر خصوصیات مکانکیی بر رفتار قالب پذیری پارچه فاستونی}, abstract_fa = {در این تحقیق رفتار قالب پذیری پارچه های فاستونی مورد بررسی قرار گرفت. بدین منظور هفت نمونه پارچه فاستونی پشم/پلی استر (% 55-45) با ساختار بافت متفاوت تهیه شد. خصوصیات مکانیکی نمونه ها نیز شامل مدول کششی (در جهت تار و پود و اریب)، مدول خمشی (در جهت تار و پود) و مدول برشی، اندازه گیری گردید. همچنین برای بررسی رفتار قالب پذیری، دستگاهی طراحی و ساخته شد. نتایج تحلیل آماری نشان داد که کلیه پارامترهای مکانیکی اندازه گیری شده تأثیر معناداری بر روی قالب پذیری دارند. با افزایش مدول کششی در جهت پود، قالب پذیری کاهش و با افزایش مدول کششی در جهت اریب، قالب پذیری در بعضی از نمونه ها افزایش یافت. همچنین مشاهده شد که با افزایش مدول خمشی، قالب پذیری کاهش می یابد. مدول برشی بر روی قالب پذیری تاثیرگذار است و با افزایش قالب پذیری، مدول برشی افزایش می یابد.}, keywords_fa = {قالب پذیری,مدول برشی,مدول خمشی,مدول کششی}, url = {https://www.jtst.ir/article_484.html}, eprint = {https://www.jtst.ir/article_484_a761cb73323cbe2d9e8d87218ce0676f.pdf} } @article { author = {Emami, F. and Shushatri, A.M. and Tavanaie, Mohammad Ali}, title = {A Feasibility Study on Producing of High Tenacity Polyethylene Terephthalate Multifilament Yarn with Optimization of Drawing Process Parameters}, journal = {Journal of Textile Science and Technology}, volume = {2}, number = {1}, pages = {15-20}, year = {2012}, publisher = {Today Textile Institute}, issn = {2151-7162}, eissn = {2322-2417}, doi = {}, abstract = {In this research, the effect of some drawing parameters on the physical properties of polyester filament yarn was investigated. Heating operations were carried out with two methods: simultaneous (heating with drawing) and sequential (heating after drawing). The results showed that the tenacity and initial modulus of PET yarns increased with increasing the draw ratio at a selected optimum heating operation. The simultaneous method gives rise to the resultant drawn yarn with superior tensile properties and low shrinkage.}, keywords = {Drawing process,Heat treatment,physical properties,PET flament yarn}, title_fa = {مطالعه امکان تولید نخ چند رشته ای پلی استر یکسره با استحکام زیاد با استفاده از بهینه سازی متغیرهای فرآیند کشش}, abstract_fa = {در این پژوهش تاثیر برخی از عوامل فرآیند کشش مانند نسبت کشش، تعداد دور پیچش نخ حول غلتک گادت و دمای عملیات حرارتی بر خواص فیزیکی نخ پلی استر یکسره مورد مطالعه قرار گرفته است. دو روش عملیات حرارتی همزمان با کشش یعنی اعمال حرارت بین غلتک تغذیه و کشش و عملیات حرارتی در انتهای کشش یعنی اعمال حرارت روی غلتک کشش با استفاده از یک دستگاه کشش صنعتی، در این تحقیق مورد بررسی قرار گرفته است. نتایج نشان داد که با افزایش نسبت کشش، استحکام و مدول اولیه افزایش یافته و میزان این افزایش شدیدا به نحوه عملیات حرارتی و نسبت کشش بستگی دارد. از میان دو روش عملیات حرارتی اعمال شده، روش عملیات حرارتی در انتهای کشش نتایج مطلوب تری را در خواص فیزیکی مانند استحکام، مدول اولیه، کار تا حد پارگی و جمع شدگی نسبت به عملیات حرارتی همزمان با کشش ایجاد می نماید.}, keywords_fa = {فرآیندکشش,عملیات حرارتی,خواص فیزیکی,نخ یکسره پلی استر}, url = {https://www.jtst.ir/article_486.html}, eprint = {https://www.jtst.ir/article_486_7bf55f5808ae8aeb100f52e450dd127c.pdf} } @article { author = {Heidari Golfazani, M.E. and Valipour, P. and Ali Bagheri, H.}, title = {A Study on the Effect of Nano Organocalay on Morphology and Dyeability of Polypropylene/ Polyamide 6 Blend Nanocomposite Fibers}, journal = {Journal of Textile Science and Technology}, volume = {2}, number = {1}, pages = {21-26}, year = {2012}, publisher = {Today Textile Institute}, issn = {2151-7162}, eissn = {2322-2417}, doi = {}, abstract = {Polypropylene fibers don’t have comfortable properties such as moisture absorption, dye absorption and good handle. Blending to produce blend composite fibers is a method for modifying properties of synthetic fibers. Another method is modifying of synthetic fibers properties with modifier materials such as nano organoclay and nano carbon. In this paper the effect of compatibilizer (PP-g-MAH) and nano organoclay Closite 15A on the microfibrillar structure of Polypropylene / Polyamide6 nanocomposite fiber were investigated. The samples with the same blend ratio (PP/PA6 70/30) but varying in organoclay content (3, 5 percent) was prepared with and without the compatibilizer by using a melt compounding process in an internal mixer. The blended samples melt spun in a single screw extruder to prepare the blend fibers. The organocally partitioning and microfibrillar morphology development of PP/PA6 nanocomposite fibers were studied with wide angle X-ray diffraction (WAXD) and scanning electron microscopy (SEM). The results show that the sizes of PA6 disperse particles and nano organoclay intercalation and/or exfoliation on the blend nannocomposite was controlled by nano organoclay percentages and presence or absence of compatibilizer. Furthermore the dyeability of PP/PA6 nanocomposite fibers with Acid milling dye is modified and increased on exhustion dyeing bath in the presence of nano organoclay.}, keywords = {Nanocomposite,Multi component Fibers,Nanocaly,morphology,Dyeability}, title_fa = {بررسی تاثیر استفاده از ذرات نانورس بر مورفولوژی الیاف نانوکامپوزتی بر پایه پلی پروپیلن/ پلی آمید 6 و خواص رنگپذیری آنها}, abstract_fa = {الیاف پلی پروپیلن فاقدخواص مطلوبی چون جذب رطوبت، جذب رنگ و زیردست مناسب می باشند. یکی از راه های تغییر و بهبود خواص الیاف مصنوعی، ترکیب پلیمرها با یکدیگر و تولید الیاف آلیاژی است. از دیگر روش های اصلاح خواص الیاف مصنوعی استفاده ازمواد اصلاح کننده نظیر نانو ذرات رس و کربن می باشد. در این تحقیق تاثیر استفاده از سازگارکننده پلی پروپیلن پیوندشده بامالئیک انیدرید (PPgMAH) و نانو ذرات رس از نوع کلوسیت A15 بر تشکیل و توسعه ریزساختار در الیاف نانو کامپوزیتی بر پایه پلی پروپیلن/پلی آمید 6 (PP/PA6) با ترکیب 30/ 70 مورد بررسی قرار گرفته است. نانو کامپوزیت ها با دو درصد متفاوت از نانو رس (3 و 5 درصد) در حضور یا عدم حضور سازگارکننده درون مخلوط کننده داخلی مخلوط شده و چگونگی توزیع ذرات نانو رس و مورفولوژی نانو کامپوزیت ها و الیاف حاصل از آن به ترتیب با آزمایش پراش اشعه X با زاویه باز و میکروسکوپ الکترونی پویشی مورد بررسی قرار گرفت. نتایج نشان می دهد که سایز فاز متفرق و توزیع ذرات نانو رس در اجزای آلیاژ با انتخاب درصد مناسب نانورس و سازگارکننده قابل کنترل است. همچنین خواص رنگ پذیری الیاف آلیاژی PP/PA6 درحضور اصلاح کننده نانو رس افزایش یافته و قابلیت رنگرزی با رنگزای اسیدی به روش رمق کشی را ایجاد گردیده است.}, keywords_fa = {نانوکامپوزیت,الیاف چندجزئی,نانورس,مورفولوژی,رنگپذیری}, url = {https://www.jtst.ir/article_488.html}, eprint = {https://www.jtst.ir/article_488_73e881e009cbb0c424e000965bf69a1f.pdf} } @article { author = {Shanbeh, M. and Ranjbaran Aman, M. and Adeli, B. and Ataeian, Arash}, title = {Investigation on the Effect of Heat setting on Twist Liveliness and Tensile Properties of Cotton-Covered Polyester Core Spun Yarns}, journal = {Journal of Textile Science and Technology}, volume = {2}, number = {1}, pages = {27-31}, year = {2012}, publisher = {Today Textile Institute}, issn = {2151-7162}, eissn = {2322-2417}, doi = {}, abstract = {Core-spun yarns can be produced by ring, rotor, friction, and air-jet spinning systems. Production of core-spun yarns on ring spinning system is known as the oldest one. The aim of this study is to investigate the effect of dry and saturated steam heat setting on twist liveliness and tensile properties of core-spun yarns containing cotton fiber as sheath and 70 denier fully drawn multifilament polyester yarn as core part. Pre-tension of core part was changed in two levels i.e. 0 and 45g and English twist factor was also varied in 3.5 and 4.0. On the other hand, 120, 150, and 180°C were selected as dry heat setting temperature. Totally, 16 different samples were tested. The twist liveliness and tensile tests were carried out on samples before and after heat setting process and then obtained results were evaluated statistically using one-way analysis of variance, Tukey and Duncan tests. The dominant reduction of twist liveliness after heat setting was observed and the samples treated with saturated steam heat setting have the lowest values of twist liveliness.}, keywords = {Core-spun yarns,tensile properties,twist liveliness,dry heat setting,saturated heat setting}, title_fa = {بررسی تاثیر تثبیت حرارتی بر میزان تاب زندگی و خصوصیات کششی نخ های مغزی دار با رویه پنبه و مغزی پلی استر}, abstract_fa = {نخ های مغزی دار را می توان با استفاده از سیستم ریسندگی رینگ، چرخانه ای، اصطکاکی و جت هوا تولید نمود؛ در این میان، ریسندگی رینگ قدیمی ترین روش تولید به شمار می آید. هدف از این تحقیق، بررسی فرآیند تثبیت حرارتی خشک و بخار اشباع نخ های مغزی دار با رویه پنبه و مغزی نخ فیلامنت پلی استر 70 دنیر کشیده شده بر روی میزان تاب زندگی و خصوصیات کششی است. در فرآیند تولید نخ های مغزی دار، کشیدگی اولبه اعمالی به جزء مغزی، در دو سطح 0 و 45 گرم و فاکتور تاب انگلیسی، در دو سطح 3/5 و 4/0 تغییر داده شد. دمای تثبیت خشک نیز در سه سطح 150 ،120 و 180 درجه سانتی گراد بود. در مجموع 16 نمونه متفاوت حاصل شد. آزمایش های تاب زندگی و خصوصیات کششی قبل و پس از فرآیند تثبیت بر روی نمونه ها انجام گرفت و در نهایت با استفاده از آزمون های آنالیز واریانس یک طرفه،توکی و دانکن، اختلاف ببن نتابج از نظر آماری مورد بررسی و تحلیل قرار گرفت. نتایج حاصله نشان دهنده ی کاهش محسوس میزان تاب زندگی نخ ها پس از فرآیند تثبیت بود. نمونه های تثبیت شده با استفاده از بخار اشباع کمترین میزان تاب زندگی را در مقایسه با روش خشک در دماهای مختلف نشان دادند.}, keywords_fa = {نخ های مغزی دار,خصوصات کششی,تاب زندگی,تثبیت خشک,تثبیت بخار اشباع}, url = {https://www.jtst.ir/article_493.html}, eprint = {https://www.jtst.ir/article_493_155b16f8e1092d455d142ae12614b352.pdf} } @article { author = {Arshi, A.}, title = {A Research on the Role of Relative Humidity on Adhesion Force of Plain Knitted Cotton Fabrics in Warm Environments}, journal = {Journal of Textile Science and Technology}, volume = {2}, number = {1}, pages = {33-37}, year = {2012}, publisher = {Today Textile Institute}, issn = {2151-7162}, eissn = {2322-2417}, doi = {}, abstract = {The behaviors such as smoothness, softness and roughness of fabrics, effectively, are related to fabric structure and physical properties of the material’s fiber. The purpose of this research is the study of influence of relative humidity on adhesion force and frictional properties of plain knitted cotton fabrics. Because of these fabrics directly contact to body skin, therefore it is necessary to determine the role of relative humidity on the fabric pleasantness. In order to this purpose, cotton plain knitted fabrics as subjected to different relative humidity (25%, 50%, 75% and 100%) in the same warm environments (T=50°C). Then the frictional parameters were obtained by using of methods friction. The results showed that relative humidity has statistically significant difference on frictional parameters, thus with rising relative humidity values (in 50°C), decrease resistance friction. Also other results determined the highest roughness values and adhesion force belonged to 25% RH, while the least adhesion force of surfaces happened in 100% RH.}, keywords = {Plain knitted cotton fabrics,Relative humidity,Temperature,Adhesion,Roughness,Frictional resistance}, title_fa = {مطالعه نقش رطوبت نسبی بر نیروی چسبندگی سطوح پارچه های حلقوی پودی ساده پنبه ای در محیط های گرم}, abstract_fa = {بروز رفتارهای همواری، نرمی و زبری از سطوح بافت، شدیداً تحت تاثیر عوامل ساختمانی و همچنین ماهیت فیزیکی الیاف بافت می باشد. هدف از اِین پژوهش، مطالعه تاثیر رطوبت نسبی محیط بر میزان چسبندگی و خواص اصطکاکی پارچه های حلقوی پودی ساده پنبه ای است. از آن جا که این نوع پارچه ها، معمولاً در تماس مستقیم با پوست بدن قرار می گیرند، لذا تأثیر تغییرات رطوبت نسبی محیط بر روی مطبوعیت و نیز چسبندگی سطوح پارچه (ها) مقایسه و مورد ارزیابی قرار گرفت. به منظور دست یابی به این هدف، پارچه های حلقوی پودی ساده پنبه ای تحت تاثیر رطوبت نسبی های متنوع (%25 ،%50 ،% 75 و % 100)، در شرایط یکسان دمایی گرم (50 درجه سانتیگراد) قرار داده شدند. سپس پارامترهای اصطکاکی آنها به روش اندازه گیری اصطکاک به دست آمدند. نتایج نشان داد که رطوبت نسبی محیط به طور معنی داری بر رفتار اصطکاکی این پارچه ها تاثیر دارد، به گونه ای که با افزایش میزان رطوبت نسبی محیطی، مقدار مقاومت اصطکاکی این بافت ها کاهش می یابد. همچنین نتایج دیگر حاکی از آن بودند که بیشترین خواص ناهمواری و میزان چسبندگی سطحی پارچه های پنبه ای در شرایط رطوبتی خشک % 25 و کمترین آن، در رطوبت نسبی %100 رخ می دهد.}, keywords_fa = {پارچه حلقوی ساده پنبه ای,رطوبت نسبی,درجه حرارت,چسبندگی,ناهمواری,مقاومت اصطکاکی}, url = {https://www.jtst.ir/article_495.html}, eprint = {https://www.jtst.ir/article_495_ab9f33fa8f7e4892b7b4d4aaea5e1e4d.pdf} } @article { author = {Tehrani Dehkordi, M. and Nosraty, H. and Shokrieh, M.M.}, title = {A Study on the Effect of Basalt and Nylon Yarns Hybridization on the Tensile Properties of Their Weaved Fabrics}, journal = {Journal of Textile Science and Technology}, volume = {2}, number = {1}, pages = {39-44}, year = {2012}, publisher = {Today Textile Institute}, issn = {2151-7162}, eissn = {2322-2417}, doi = {}, abstract = {In spite of numerous advantages of polymer composites, these materials have some weakness to compare of metals. To solve these problems, the fabrics with special mechanical properties (same as basalt-nylon fabric) were produced in the form of both homogeneous and hybrid. To improve the impact performance of composite materials, in this study for the first experience, after preparing of yarn and adjusting and modifying in ordinary rapier loom, homogenous and hybrid fabrics of basalt and nylon were fabricated. For hybrid fabrics, the percentage of nylon or basalt is equal in the warp and weft directions. After fabricating, the tensile behavior of prepared fabrics was tested. The results show, however the strength of hybrid fabrics was lower than the homogenous ones but the hybrid fabrics had a stepwise fracture. Therefore the hybrid fabrics can prevent to the accident fracture in composite materials.}, keywords = {weaving,hybrid fabric,basalt,Nylon,tensile properties}, title_fa = {بررسی تاثیر ترکیب نخ های بازالت و نایلون بر خواص کششی پارچه های بافته شده از آنها}, abstract_fa = {مواد کامپوزیتی با وجود مزیت های زیاد، مشکلاتی نیز در مقایسه با فلزات دارند. برای حل این مشکلات، تولید پارچه های تقویت کننده دارای خواص مکانیکی مشخص به صورت خالص و مرکب از نخ های مختلف همچون بازالت و نایلون از اهمیت ویژه ای برخوردار است. در این تحقیق برای بهبود آسیب پذیری کامپوزیت ها در برابر ضربه، پارچه های خالص و مرکب از جنس بازالت و نایلون تولید گردید. در پارچه های تولید شده درصد الیاف بازالت و نایلون با درصدهای مختلف بر روی یک ماشین بافندگی رپیری در هر دو راستای تار و پود مشابه نیز، تغییر کرده است. پس از آماده سازی پارچه های بافته شده، رفتار آنها در برابر کشش مورد بررسی قرار گرفت. نتایج نشان می دهد اگر چه استحکام نمونه های مرکب از نمونه های خالص کمتر می باشد، اما نحوه شکست در نمونه های مرکب به صورت پله ای صورت گرفته است. بنابراین استفاده از این پارچه ها می تواند از متلاشی شدن سریع و ناگهانی کامپوزیت ها جلوگیری کند.}, keywords_fa = {بافندگی,پارچه مرکب,بازالت,نایلون,خواص کششی}, url = {https://www.jtst.ir/article_496.html}, eprint = {https://www.jtst.ir/article_496_10d32422b138e2e0badb801e32a0ca5d.pdf} }